 |
 |
Line Items: 0
Total Items: 0
Sub Total: $0.00 |
|
CURRENT
SHOPPING
CART STATUS
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪
Applicable Tax and Freight Charge will be added to Final Invoice.
|
|
|
|
|
|
RKI Beacon 200 Fixed Gas
Detector |
|
 |
-
Simultaneous readout
on 2 channels
-
2 Alarm levels per
channel
-
Discrete and common
relays
-
NEMA 4X enclosure
-
4-20 mA outputs
-
Proven long-life
sensors for a wide variety of gases
-
Accepts any 4-20 mA
transmitter input
-
Easy to install,
operate and expand
-
SENSORS SOLD
SEPARATELY - ORDER SENSORS
-
Beacon 110
-
Beacon 800
Beacon 200 Gas Detector Manual |
| |
|
The Beacon 200 is a powerful, 2 point, low cost fixed system controller
that is microprocessor controlled, versatile, simple to install and
operate. It is capable of connecting RKI sensors directly for LEL
level combustibles, Oxygen, Hydrogen Sulfide, or Carbon Monoxide.
The Beacon 200 can also accept any 4-20 mA
transmitter (2 or 3 wire, 24 VDC). Sensors can be mounted directly
at the Beacon 200 housing or wired remotely from the controller.
The digital display has backlighting capabilities and simultaneous
readouts of the gas type and concentration.
The 10 amp rated relays are strong enough
to actuate most external alarms and horns without using slave relays.
The Beacon 200's housing is rated NEMA 4X for corrosion resistance and a
weather tight seal and complies with lock-out/tag-out standards.
An external reset switch allows the alarm to be silenced from outside
the controller housing. The Beacon 200 comes complete with a wall
mounting kit for easy installation.
RKI offers the industry's widest selection
of standard and toxic gas detection sensors, which can be utilized with
the Beacon 200, providing gas monitoring protection for almost any
application. |
| |
|
PURCHASE BEACON 200
|
|
ITEM
NUMBER |
DESCRIPTION |
PRICE |
|
|
Beacon 200
(2) Channel Controller* |
|
|
* Please note: This unit
does not come with sensors - you must purchase the sensors
separately |
|
|
|
|
BEACON 200 SPECIFICATIONS
|
| Dimensions |
10.5" x 8.5" x 6.3" |
| Enclosure |
Wall mounting grey polycarbonate with
hinged cover |
| Conduit Connection |
3/4" NPT conduit hubs, 3 provided,
2 for sensor wiring and 1 for power and relay wiring |
| Wiring termination |
Screw type terminal block, 14 gauge
max |
| Controls |
4 internal push buttons for setup,
programming and calibration
1 external push button for alarm reset |
| Operating Temp |
14 to 122 degrees F (-10 to 50
degrees C) |
| Storage Temp |
-4 to 158 degrees F (-20 to 70
degrees C) |
| Relative Humidity |
0-100% RH |
| Enclosure Rating |
NEMA-4X enclosure, waterproof,
chemical and weather resistant |
| Direct Wired Sensors |
LEL, Oxygen, Carbon Monoxide,
Hydrogen Sulfide
Remote amp not required for less than 500 feet |
| 4-20 mA Sensors |
Accepts any 4-20 mA transmitter (24
VDC, 2 or 3 wire). A wide variety of RKI sensors are available
with 4-20 mA signals. Wiring distances up to 5000 feet |
| Sampling Methods |
Diffusion and sample draw heads
available |
| Relays |
7 relays, 10 amp rating (at 115 VAC), SPDT isolated contacts
2 relays for common gas alarm and 1 common relay for malfunction
Relays fully programmable for: increasing or decreasing alarms,
latching or self reset, normally energized or normally
de-energized, time delay for alarm on and alarm off. |
| 4-20 mA |
Signal output, 4-20 mA (into 1000
ohms impedance max), per channel |
| 24 VDC |
24 VDC (350 mA max) output provided to operate
sample drawing adapters or other accessories |
| Display |
Alphanumeric display with
backlighting. 20 characters per line; 4 lines each |
| Audible |
Built-in audible alarm, 94 dB,
mounted on enclosure
Coded ouput: pulsing = gas alarm, steady
= fail |
| Visual |
4 LED alarms on front cover
for alarm indications, pilot, and malfunction |
| Optional expansion cards |
Individual 4-20 mA (or 1-5 VDC)
outputs
Heavy duty relay card (4 each @ 30 amps) |
| Power |
115 VAC or 12 VDC standard.
Optional 230 VAC. Battery backup option available |
| Warranty |
1 year materials and workmanship |
|
|
|
